x – Let'sFly3D http://www.letsfly3d.com Advanced 3D printing for the hobby pilot Tue, 17 Jan 2017 14:14:51 +0000 en-US hourly 1 https://wordpress.org/?v=6.5.2 http://www.letsfly3d.com/wp-content/uploads/2016/06/cropped-3d-1-32x32.png x – Let'sFly3D http://www.letsfly3d.com 32 32 X-Frame GoPro Session Mount http://www.letsfly3d.com/product/x-frame-gopro-session-mount/ Sun, 27 Nov 2016 07:10:25 +0000 https://www.letsfly3d.com/?post_type=product&p=907 GoPro Session Mount for X-frames]]>

This GoPro Session mount was built for the UBad Katana, but works with most x-frames featuring a flight controller-stack mounting shape. 

 

Made from TPU, it is nearly indestructible, and will help protect your gopro session.

 

Camera angle at 35 degrees.

]]> Kama Pod http://www.letsfly3d.com/product/kama-pod/ Wed, 28 Sep 2016 01:21:47 +0000 https://www.letsfly3d.com/?post_type=product&p=682 The UBAD Kama is a work of art.  With this 3d printed pod, it looks even better.   But, not only that, it protects the flight controller, vtx, and rx from grass and water from the morning dew.  (I didn’t say waterproof, it’s not the iPhone…)

 

(ESC covers, and vtx mount not included – if Katana VTX mount is purchased on the same order – or if it is purchased with a comment that it is for the Kama, it will be sent with 2 standoff spacers)

 

It is designed for a 2.1 or a 2.5mm lens, to allow the camera to notch into 30, 45, and 60 degree slots.  An adapter ring will be included to allow for 2.8mm lens.

 

This pod does not come with hardware – you will need to source 4 m3 screws, 4 nuts (non-nylon – to be inserted into the pod) and 2 longer screws for your fpv camera.

For the standard hs1177, I used servo screws that I had laying around, but for the Foxeer camera, I needed to source some longer m2 screws.

 

examples (length may vary):

 

 

]]> X Frame – Receiver Mount http://www.letsfly3d.com/product/x-frame-receiver-mount/ Tue, 26 Jul 2016 20:33:48 +0000 https://www.letsfly3d.com/?post_type=product&p=559 This was designed for the UBAD Katana, but should fit most x frames with pdb/flight control-style mounting.

This will fit frsky x4r/d4r/xsr and spectrum satellite receivers (x4r and d4r need to be depinned).

 

]]> X Frame – VTX/XT60 Mounts http://www.letsfly3d.com/product/x-frame-vtxxt60-mounts/ Tue, 26 Jul 2016 20:20:25 +0000 https://www.letsfly3d.com/?post_type=product&p=547 The X Frame XT60 and VTX mounts were designed for the UBAD Katana, but fit most x frame quads that use standoffs on top of the flight controller.

These mounts were designed to take the place of the spacer between the pdb and flight controller.  They are 10mm high.

(4) 25mm m3 screws are recommended to mount the pdb and flight controller for adequate space.

This is packaged as one of each: one VTX and one XT60 mount.

]]>